CAD & 3D Printing Thread

[NTP66]

I'm tempted to print out the lid just to show you what it should look like...

[NTP66]

I printed out a bunch of Multiboard tiles, and then designed some holders for a number of my tools in onshape and printed them. This allowed me to hang the stuff I regularly use and free up space in the drawer for other things. Total print time was around 14 hours.

[CBear3]

Nifty. May need to print some of that stuff for my workshop.

[NTP66]

I printed the tiles in PETG, though it seems like most just use PLA unless you live in a crazy hot climate. The system can be confusing with all of the different connection types, but definitely sturdy. I used E-Z Anchors for the tile mounts to the drywall, since my studfinder managed to incorrectly locate the studs. I didn't center the tiles over my printer because I wanted to avoid that air gun randomly dropping on top of my AMS unit and cracking the lid.

[NTP66]

Just started a new multi-piece print for my daughter. Three plates total, and two of them are over 19 hours each. I may actually start those ones late so that any issue, like a filament runout, is likely to happen in the morning instead of the middle of the night.

[NTP66]

Two hours into the 20 hour print and the PTFE guide I printed and installed in my hot end snapped, resulting in a failure. Removed the broken piece and reseated the PTFE and resumed printing. Really hope it gets though this print without issues, as there are something like 450 filament changes, so a lot of retraction/etc. events.

[Beveridge]

I printed out a bunch of Multiboard tiles, and then designed some holders for a number of my tools in onshape and printed them. This allowed me to hang the stuff I regularly use and free up space in the drawer for other things. Total print time was around 14 hours.

I was jamming to that video.

[NTP66]

I was jamming to that video.

I was having trouble coming up with some kind of music for the background so you're not just staring at silence, then it popped into my head to try... and it works.

[NTP66]

My daughter's favorite X-Men character is Storm, so I had to give this print a try. Total print time was around 38 hours.

[NTP66]

I wanted to test the functionality of the new poop chute, which divers everything to a bin directly under the printer's shelf, so I printed this cute little articulating whale shark. New chute works perfectly.

[iamjs]

decided to try to try to print a mini curling stone. 90 minutes later, I'm noticing that it might not be mini.

I have a feeling it will still be printing when I leave for work 10 hrs from now.

[NTP66]

I found a 64 Corvette model that I may print for my dad. OrcaSlicer currently shows it as a 1d32m print.

[iamjs]

I ended up stopping it because it was printing outside of the boundaries and causing flat spots. After two hours, it barely had the surface printed.

If I had to estimate how much time was left when I stopped it, I would have guessed probably closer to 14-16 hours.

[NTP66]

Does Flashforge's slicer not give you an estimate of how long the print will take? That seems crazy to me. OrcaSlicer will not only show you print time, but also show you how much filament will be used for each layer type, etc.

[iamjs]

It gives me a estimate on filament used, but it seems like it's very basic software. I was playing around with Slic3r last night and it seems like it's a little more detailed.

The one thing that I don't like so far is that the printer itself won't pick up my wifi or even the hotspot from my phone. It sees every broadcasted channel within a 300 ft radius of my place, but it won't see my router which is maybe 10 ft away in the garage. So for now, I have to convert everything, transfer to USB and print from the USB stick. Not that big of a deal since it's only an extra 15 seconds of shuffling stuff from point A to point B, but puzzling nonetheless. I kicked around doing a factory reset on it, but I'm not that annoyed by it yet.

[NTP66]

You might want to give OrcaSlicer a try, as well. They have a number of Flashforge printers in there, though I don't see your exact model. I bet you could use one of the others, or at least create a custom one.

[NTP66]

Sneak peak at my next print, likely a Father's Day gift for my dad.